How to build a flat earth map with a flat top

Posted November 20, 2018 08:24:38 I have an idea.

How about I go to my local lumber yard and show them how I build my flat top flat earth maps.

I am sure they will give me the green light to make them.

I have no idea how many people are using flat tops but I have seen a few hundred people build their flat tops.

The flat top is one of the simplest flat top types of maps.

You can make a flat map using a simple line drawn on a paper map board.

A flat top map is also called a “dots” map.

When I saw the flat top, I had to try it out.

The instructions for building flat top maps are on this website.

I think I have it all figured out.

You must make a rectangular flat top.

You may need a ruler to measure the lines on the paper map and draw them on the flat bottom.

Use a pencil to draw a line across the flat tops, and then make a mark on the line with a pencil or marker.

Then place the flat board on a flat surface.

When you have finished building your flat top line, mark the line on the map on the top of the map.

You should have two lines on each side of the flat map.

The first line is for the flat surface you are working on.

This line is usually made of one-inch or two-inch lines of tape.

The tape will not make any marks on the maps you make.

The second line is the map center.

The center line is made of two or more lines of black tape, usually 1/2 inch.

If you have a map center tape, you can use that tape to mark your center line on your flat map, too.

You will want to mark the center line of each flat top with a piece of tape, about 1/8 inch in diameter, or a pencil mark.

When the flat base is on the surface of the maps, place it on top of your map center and make a marking with the pencil or ruler.

The marks you make will help you determine the location of the center lines and help you figure out the location.

To build the flat maps you will need a flat bottom, such as a wood or cardboard board.

If your flat bottom has tape on it, you may be able to use that.

You need a line of tape about 1-inch long to make a line that will cover the flat bottoms.

You also need a pencil that has a rounded tip.

I used a pencil with a sharp point.

I was using a pencil for my flat tops and a pencil without a sharp tip for my maps.

If it doesn’t work for you, try putting your flat tops on a board with a wooden base.

When your flat maps are built, you should have about a half-inch of tape left on the bottom.

You could also put a rubber band or two around the bottom of your flat base and tape it down with tape.

When finished, tape the tape around the top edges of your maps.

Make a mark in the tape with a ruler or pencil, and place the map back on the board.

Now place the board under the flat boards and tape the top over the mark.

Do not tape the edges of the tape.

This is important.

You want the tape to stick to the map, so that the flat lines on it will not move.

You might also need to put tape around your flat board and tape over the marks made by the flat-top markers on the base.

Make another mark on your map, just above the mark you made earlier.

The next step is to make two flat tops of the same size.

This will make the flat bases of two flat top models.

You’ll want to make one flat top for each map.

Put your flat bases on the table, with one of your top flat tops facing the table.

You are making the flat sides of your bases as flat as possible, so they won’t be rounded.

Use the ruler or pen to draw the center mark on both flat tops so that they will have a rounded bottom.

Make two marks on each flat surface, one on the first flat top and one on each of the second flat tops that are on the opposite side of your table.

Mark them with a marker.

Place the top flat top back on its flat base.

Tape a second mark on each top.

This time mark the middle mark on one flat surface and the center on the other.

You now have two flat bottom maps.

Place them back on their flat bases.

You have now made two flat maps.

Now you need to build one flat bottom map.

To make one, draw a circle on the inside of the first map.

Cut the circle to a half inch in length, and cut it into two half-inches squares.

You do not need to cut the circle into a perfect circle.